Due to their lack of understanding of electric floor heating product systems, many consumers have some deviations in their understanding of electric floor heating products and in their daily use. They mistakenly believe that graphene floor heating products consume a lot of electricity and are very expensive during daily use. In fact, judging from the use experience, graphene floor heating is a green, energy-saving and environmentally friendly floor heating product.

For users who want to know about or have installed a graphene floor heating system, they will pay attention to its energy saving issues whether they are learning about the product or starting to use it. However, many people still maintain the habit of using air conditioners, turning them on as soon as they are used, and turning them off as soon as they leave. They think that they only need to turn on the electric heating system when the room needs to be heated, and turn off the heating system when going out to save energy. There is a huge difference between floor heating and air conditioning. The heating cost is likely to increase during the process of turning on and off. So how to use floor heating to be more energy-saving?

Graphene floor heating consumes more power “out of the box”

 

"Ready-to-use" air conditioner

"Ready-to-use meetings are more energy-saving" is a misunderstanding caused by long-term use of air conditioners. The air conditioner outputs the heat required for heating through the vents of the indoor unit to increase the temperature of the entire indoor air. Wherever the warm air can blow, you feel hot, and where it cannot blow, it is still cold. The heat only flows in the air in a local area of the room and does not heat the floor and walls. Therefore, the room temperature will drop within a few minutes after the air conditioner is turned off. It is reduced to the same as before, without any heat storage capacity, and it is obviously more energy-saving to open it immediately.

 

Graphene floor heating heating method

Floor heating is different from air conditioning in that floor heating supplies heat to the room through the ground through radiation and convection heat transfer. After the graphene floor heating is started, the ground continuously absorbs heat and makes the indoor temperature reach the set temperature through thermal radiation. It only needs to supplement the heat of the heat-consuming part of the house to maintain the set room temperature. At this time, the heat required is much smaller. The operation of turning on and off immediately will waste a lot of heat in heating the ground floor, thereby increasing the cost of floor heating.

 

The cost of heating depends on the insulation performance of the house.

First of all, a house has good thermal insulation, which helps reduce the heat dissipation of the house. The amount of heat that needs to be supplemented by floor heating will be smaller, which is more energy-saving. Secondly, keeping the ground at a certain temperature can also avoid a large amount of heat consumption, and only need to replenish the heat. The heat dissipation of the house is enough.

 

Proper temperature regulation and use of heating systems

heating up for the first time

If the electric heating film heating system is installed, it should be heated up slowly for the first time or if it has not been started for a long time. When starting the electric heating film heating system for the first time, the system should be set at 13℃-15℃, run in the low temperature range for a period of time, and then increase the temperature in steps of 2℃ until it reaches the comfortable heating temperature.

picture

Temperature adjustment

Once the floor heating system is turned on, try not to turn it off during the heating period. Users can set the temperature according to their needs through the smart thermostat according to their respective living and working hours, which helps save energy consumption. Frequently opening and closing the thermostat will cause the electric heating film to frequently change its working state, which will not only cause poor heating effects, but also greatly increase heating costs, which is counterproductive.

Avoid heat loss

Because the graphene heating film floor heating system is a mild heating system, frequent and long-term opening of doors and windows has a considerable impact on the heating effect and energy consumption. Therefore, during the heating period, special attention should be paid to the sealing of doors and windows, and the number of openings of doors and windows should be reduced as much as possible. Ventilation should be arranged at noon when the sun is sunny to avoid heat loss.

Notice

People can set the indoor temperature at 13-15°C when leaving home. About an hour before returning home, they can use the remote control function of the intelligent temperature control to set the indoor temperature to about 20°C in advance. This not only heats up quickly, but also More energy efficient. If there is no one at home for a long time, for example, if there is no heating for several days, it is recommended to turn off the floor heating and turn it on when needed. Furthermore, if there is no one in the room and there are no activities, the doors and windows in this area can be closed. After isolation, the floor heating system in this area can be turned off at the same time to achieve greater energy saving.

picture

Graphene floor heating not only meets the heating needs of users, but also conforms to the general environment of energy conservation and environmental protection. Social and economic development is getting better and better. With the basic material satisfaction of life, more and more people are pursuing a higher quality of life. As an electric heating product that is safe, convenient, highly comfortable, energy-saving and environmentally friendly, and can also meet people's individual needs, what reason is there to reject graphene floor heating?